How To Clean A Chainsaw

Here is a list of what you need before you start the clean-up process

• Screwdriver- this is used during the reassembling and assembling process.
• Dry cloth- used to dry the chain saw parts.
• Scrapper- it is used for scraping off any hard residue that is stuck on the chainsaw.
• Pipe cleaner/ wire- you can use a pipe cleaner or a wire to unblock any holes.
• Stiff brush- this is used to clean off excess dirt
• Water- You should use warm, soapy water to remove stubborn stains.
• Ammonium – is used as a solvent to soak the gas tank and fuel filter.

What you need to take caution when cleaning the chainsaw

• After reassembling everything, please place them safely to avoid losing them, especially the nuts.
• Ammonia has a bad smell, and if you use it, you should ensure your room is well-ventilated.
• You should rinse everything well to avoid rusting.
• Do not use the air compressor to dry the air filter so that you do not blow the holes.
• Place the chain on a newspaper after lubricating for any excess drip-off.

The Process of How to Clean a Chainsaw

Follow the following steps to give your chain saw a perfect look.

Step 1: Reassemble

On a work surface or a table, reassemble everything to make it easy to clean each of them. Do not forget to drain the gasoline and oil while cleaning the fuel tank. Using a screwdriver, loosen the nuts and place them in a safe area. You should disconnect the power source if you clean an electric chain or saw. This way, you will have an easy time cleaning the parts.

Step 2: Spark plug

Begin by cleaning the spark plug. It is most likely to have build-up carbon, and too much build-up can alter the functioning of the chain saw. For that reason, use a stiff brush to clean it. You might need to replace them if they are severely dirty.

Step 3: Fuel tank

To clean the fuel tank, you will need to use ammonia to clean the inside of the tank and the fuel filter. You might not need to clean the fuel tank again if you had cleaned it a month ago.

Step 4: Bar

To clean the bar, you must set the chain aside first. Using a cloth and soapy warm water, you can clean the dirt on it. Then rinse it and dry it with a dry cloth. Could you leave it to air dry to avoid rusting? If the bar is too dirty, you can use a degreaser to help clean it up.

Step 5: Chain

Mix a cup of ammonia with water in a bucket and soak it for 20 minutes. Scrub it off with a stiff brush. Then rinse it in warm water and dry it with a cloth. It would help if you left it to dry in the air too. After it is scorched, you can lubricate it with oil.

Step 6: Chain lubricating hole

Unblock the holes using a pipe cleaner or improvise a wire to clean it up.

Step 7: Carburetor

To clean the carburettor, mix water with one cup of ammonia. Then soak it in the mixture for 20 minutes before washing it. Using a stiff brush, you should scrub the excess dirt from it. Rinse it in warm water and use a dry cloth to dry it.

Step 8: Air filter

Use soapy, warm water to clean the air filter. Then use a stiff brush to clean it up gently. You might also need to replace it if it is too dirty and worn out.

Step 9: Spark arrestor

You can clean the spark arrestor by tapping it on the table or work surface. Also, you can use a small soft brush to clean it up.

Step 10: Assemble

After cleaning, you will need to put everything back into place. Ensure that you mount the chain correctly. Also, tighten the nuts to ensure that they are not loose. After everything is assembled, refill the gas and oil in the fuel tank.

What next?

Your chain saw is ready for another tree-cutting process and will be taken care of after some time. After a tree-cutting process, you should remove the bar and chain to ensure that is safe. Also, avoid storing it on a wet floor to prevent rusting. Repeat the cleaning process after a month or if it is too dirty.